Excellent NS0-593 Study Guide To Help You Prepare For Network Appliance NS0-593 Exam

Do you know the requirements for earning the NetApp Certified Support Engineer – ONTAP Specialist certification? First, you need to pass the NS0-194 exam to earn the NetApp Certified Support Engineer certification as the prerequisite. Then pass the NS0-593 exam successfully. To all, the excellent NS0-593 study guide is available online to help you pass your Network Appliance NS0-593 exam successfully. A good method to get ready for the actual NetApp NS0-593 exam is to choose the Network Appliance NS0-593 study guide of ITExamShop to practice all those questions and answers.

Check Network Appliance NS0-593 Free Demo Questions First

Page 1 of 1

 Loading...

1. The motherboard of Node-01 is being replaced. To perform this task, a takeover was Initiated from Node-02. Node-02 panics showing the string below.

PANIC; Permanent errors on all HA mailbox disks (while marshalling header) in SKprocess fnmbx_instanceWorker on release 9.5P8 (C)

What has happened in this situation?

While in maintenance mode, the sldiag device show command was executed.

While in maintenance mode, the fcadmin device_map command was executed.

While in maintenance mode, the HA_config show command was executed.

While in maintenance mode, the mailbox destroy local command was executed.

Launch demo modal

 Loading...

2. You receive the "Unable to connect to the management gateway server"error when trying to connect to a node management IP.

In this situation, how do you determine whether core dumps are generated for the mgwd user space process?

Log in to the nodeshell using the node console and collect the core dumps from the nodeshell.

Log in to the service processor and collect the core dumps from the service processor.

Log in to the clustershell using the node console and collect the core dumps from the clustershell.

Log in to the systemshell and collect core dumps from thesystemshell.

Launch demo modal

 Loading...

3. A system panic due to an "L2 watchdog timeout hard reset" error occurred. You have found a FIFO message in the SP log.

Which FIFO message Is useful for Investigating this Issue?

before NMI BBSP:C=00 L=00 FIFO: F3 F2 F1 F0 5 B2 0 0 0 80 20 E F E3 C0 C2 3 4 6 7 9 9 A

BIOS exit BBSP:C=2F L=20 FIFO: 2 C8 C9 C4 24 4 6 18 7 8 11

before Reset BBSP:C=00 L=00 FIFO:

ONTAP Shutdown BBSP:C=00 L=2F FIFO:

Launch demo modal

 Loading...

4. Your customer has deployed a two petabyte NetAppONTAP FlexGroup volume across their 4-node ONIAP 9.8 cluster. They plan to store over three billion files. They want to prevent file 10 conflicts since files are placed into the FlexGroup volume.

In this scenario, which two NFS SVM parameters should be enabled? (Choose two.)

-v3-64bit-identifiers

-v4-fsid-change

-v3-fsid-change

-v4-64bit-idantifiers

Launch demo modal

 Loading...

5. A customer's storage administrator Informs you about the deactivated Automatic Switchover (AUSO) feature on their MetroCluster IP environment.

What Information would you tell your customer in this scenario?

The AUSO feature cannot be activated due to a non-mirrored aggregate.

The AUSO feature is not available in Metrocluster IP installations by design.

A faulty link automatically deactivated the AUSO feature.

This is a configuration failure, you can activate that feature for the customer.

Launch demo modal

 Loading...

6. Referring to the exhibit, what do you need to do to return the MetroCluster to a normal state?

Enter the metroclustor switchback command on Site

Enter the metrocluster switchback command on Site

Enter the storage failover giveback command on Site

Enter the storage failover giveback command on Site

Launch demo modal

 Loading...

7. 1.After expanding a two-node AFF A300 cluster with two AFF A700 nodes, you observe latencies when data is accessed indirectly. The system node run -node -command netstat command shows retransmits and packet drops on the LIFs. The AFF A700 nodes with 40 Gbps and the AFF A300 connect with 10 Gbps to the cluster interconnect. You are using Cisco Nexus 3132Q cluster interconnect switches. You just updated to ONTAP 9.8 software.

In this scenario, what is causing this problem?

The 10 Gbps to 10 Gbps cluster Interconnect is creating a speed mismatch.

AFF A300 and AFF A700 node mixing Isnot supported in ONTAP 9.8 software.

The AFF A300 Is using an adapter card for the cluster Interconnect, but only onboard ports are supported.

There is an NXOS firmware mismatch, verify in the Interoperability Matrix (1MTJ for a supportedversion.

Launch demo modal

 Loading...