New BICSI RCDDv14 Exam Questions To Pass The BICSI Registered Communications Distribution Designer Exam

Regina2022-08-19T02:22:30+00:00

BICSI Registered Communications Distribution Designer Version 14 is available, candidates are required to pass the RCDDv14 exam successfully to earn this certification. When deciding to prepare for the BICSI RCDDv14 exam by using the online resource, we suggest you choose the new BICSI RCDDv14 exam questions from ITExamShop. By having the new BICSI RCDDv14 exam questions of ITExamShop, you can simply pass the BICSI Registered Communications Distribution Designer – RCDDv14 exam with 100% passing guarantee.

Having the BICSI Registered Communications Distribution Designer – RCDDv14 free demo questions first:

Page 1 of 4

1. Using a vertical cable support structure can create issues for the cable attached to the pathway Several issues can result It the support work is not clone correctly.

Which two of the following conditions could be caused by a poorly supported cabled (Select two options.)

Lower dB loss values

Stretching of copper conductors and breakage of optical fiber strands

Increased Interference levels

Reduced expected useful life and performance

Slippage between the cable core and the sheath

2. When preparing an upfront cost estimate, the ICT distribution designer MUST consider which two of the following fees? (Select two options.)

Taxes

Permits

Inspection

Licensing

Safety

3. The transfer of unwanted signals may occur over one path or several paths.

What method addresses the mitigation or suppression of unwanted signals?

Mounting heights in racks and cabinets

Bonding and grounding

Signal coupling

The use of unshielded cables

4. Before working on equipment, what is the FINAL step in the lockout/tagout (LOTO) procedure?

Verify the equipment controls are in the proper operating position.

Train workers to perform the LOTO process.

Apply appropriate tags both locally and remotely.

Confirm the device is de-energized by proving it will not run when started.

Confirm all unnecessary items have been removed from the area.

5. Which two of the following roles do an ICT distribution designer use to ensure a timely and cost-effective telecommunications construction project? (Select two options.)

Discuss design concerns with inspectors. AHJs, and other stakeholders.

Verify that the overall physical security design complies with the owner expectations.

Assist in the resolution of unforeseen conditions, change orders RFIs and changes to the project's critical path.

Ensure the construction materials are stored properly and protected from theft.

Coordinate electrical supply so it is available in advance of the starting of contractor work.

6. When estimating an ICT distribution designer project timeline schedule based on the scope of work which two scheduling methods use network diagrams lo integrate logical activities and identify critical paths on the project? (Select two options.)

If This Then That (IFTT)

Gantt Chart

Work Breakdown Structure (WBS)

Critical Path Method (CPM)

Program Evaluation Review Technique (PERT)

7. Which of the following is a common application for exothermic welding of earthing (grounding) and bonding conductors?

Bonding to structural steel

Locations requiring monthly maintenance

Connections made to the TBB

Cable to cable connections

8. During bidding the ICT distribution designer should review the bid responses for compliance and completeness. Afterwards, the designer should report the findings and recommendations to the

construction foreman

legal counsel

stakeholders

technical consultant

9. The size and number of conduits or sleeves used for backbone pathways depend on the usable floor space served by the backbone distribution system.

What is the MINIMUM trade size of sleeves recommended to serve a TR, ER, or EF?

10. What is the OPTIMAL lime in the construction process for ICT submittals to be reviewed by the ICT distribution designer?

After the contract is awarded and before project close out

As part of the contract bid process to prevent project delays

Before the contract is awarded

At the beginning of the close out process

Page 2 of 4

11. Conducted coupling may affect electronic devices primarily through which two of the following means'? (Select two options.)

inductive coupling (by magnetic fields)

Input signal lines

Output signal lines

Optical signal lines

Capacitive coupling (by electric fields)

12. Which of the following options BEST describes Request for Quote (RFQ)?

Usually provides more detail involved with selecting the material, equipment, and components required during implementation (e.g. make, model, performance specifications)

Can be submitted by the contractor in response to a field order or as an uninitiated request for a change in scope

Used to obtain a formal response to the contract documents

An invitation for the design professionals (e g, architect, engineer, consultant) or contractors to submit a proposal for services

13. A project's installation start involves a Kickoff Meeting and the General Contractor's Coordination Meeting. As part of the designer's responsibilities, which two of the following ate key elements of the Kick-off Meeting? (Select two options.)

Project submittal approval process

RFI process

Payment procedures

Punch List process

Project start and completion dates

14. In a budding with one join room for serving as the FR and EF and four dedicated TRs on the same floor a total of__________ 103 mm (4 trade size) conduits should be installed to interconnect the backbone pathways to the ER.

15. DRAG DROP

Identify the fibers below as either single mode (SM) or multi-mode (MM) by dragging the appropriate term into each oval.

16. What is used to facilitate MINOR changes to the Project Requirements?

Request lot Information (RFI)

Punch list

Field order

Change order

Change order request

17. An ICT distribution designer is designing a backbone cabling network that is specified for a campus network including several links approaching 2000 m (6562 It) and data rates of 100 Gb/s What optical fiber type(s) should be used?

OM3 fiber

OM4 fiber

Both OS1 and OS2 fiber

Both OS2 and OM3 fiber

18. What is the PRIMARY reason for considering a physical ting topology for connecting outlying buildings?

It is the most cost effective design ten a campus network.

It provides a redundant cable path for disaster recovery.

It is the most compelling design for any network requirement.

It is an easier physical design to install.

19. Which of the following is a consideration for lighting telecommunication spaces?

To ensure worker safety within TEs. Light level requirements are higher tor these than other spaces

The light fixtures within telecommunications spaces shall be fluorescent type fixtures.

The electrical power for lighting shall be connected to the same electrical panel as the telecommunications equipment.

The lighting layout shall be coordinated with the equipment and pathway locations

20. How many classes of telecommunications administration are there?

Page 3 of 4

21. In a PTP network using optical fiber, the ________ is responsible for media conversions from the optical fiber to the balanced twisted pair network within the residence.

ONU

ONT

OLT

OLTS

22. For optical fiber cabling, which of the following test instruments is used to locate and identify any anomalies?

OTDR

Optical power meter

OLTS

Spectrum analyzer

23. An ICT distribution designer installed a 50/1 ?5 mm/1300 nm fiber optic cable from Building A to identical Building B with a distance of 600 m (1968 ft) At Building B. the designer fusion splice this new cable to an existing identical 50/126 mm fiber optic cable that runs 800 m (2525 ft) to Building C. Both ends are terminated with SC connectors.

What is the loss budget for the above fiber link?

2.95 dB

3.40dB

3.90 dB

4.35 dB

24. Which two of the following types of metallic conduit REQUIRE threaded couplings? (Select two options.)

Electrical metallic tubing (EMT)

Aluminum metal conduit (AMC)

Flexible metal conduit (FMC)

Intermediate metal conduit (IMC)

Rigid metal conduit (RMC)

25. Which of the following statements Is CORRECT concerning best practice for horizontal cable management panels?

One RU of management panel for each RU of cable patch panel plus one additional RU of cable management

Two RU of cable management panel for each RU of patch panel

Three RU of cable management panel for each RU of patch panel

Two RUs of management panel for each RU of cable patch panel plus two additional RUs of cable management

26. An ICT distribution designer is estimating the installation of five units of 1.5 m (5 ft) tong channel basket trays connected together in the ceiling. The total length of the pathway needed is 7 5 m (25 ft).

How many supports will be needed''

27. What step can be a phase of the Bidding and Negotiating process?

Prepare necessary change orders

Identifying any conflicts that may become apparent

Creating a response evaluation

Identifying potential value engineering opportunities

28. When considering pathway types, the ICT distribution designer should consider the applicable MICE factors as defined in TIA 568 for structured cabling systems and components MICE 3 relates to

commercial environment

heavy industrial environment

medical environment

light industrial environment

29. During the design phase, drawings for ICT communications spaces should be reviewed for Standards compliance and

cost projections. B OSHA specifications

client requirements

equipment availability

30. Which of the following terms is often used to describe two parallel paths that have identical conductive terminations to two separate grounding reference points?

Resistive loop

Ground loop

Capacitive loop

Inductive loop

Conductive loop

Page 4 of 4

31. A 3 trade size conduit is sized at

78 mm (3 in)

91 mm (3 1/2 in)

103 mm (4 in)

129 mm (5 in)

32. When designing an underground conduit system, a single bend should be NO MORE THAN ________ degrees.

120

33. In a RFI, an ICT distribution designer instructs the contractor to test all the fibers In a PON Installation.

Which of the following testing requirements does the designer include?

Uni-directional 850 nm and 1300 nm

Bi-directional 850 nm and 1300 nm

Uni-directional 1310 nm and 1550 nm

Bi-directional 1310 nm and 1550 nm

34. What's the RECOMMENDED twisted pair cable slack length to be left at the work area outlet location to enable the possibility of future changes in the Horizontal Cabling System?

=0.152 m (0.5 ft)

=0.3 m (1 ft)

=1 m (3 ft)

= 5m (16 40 ft)

35. You have just finished a design calling for 15 telecommunications outlets. You received word that the owner has increased his requirements by 40%.

What size commercial DD (distribution device) is required to accommodate the increase?

660 mm (26 in)

1015 mm (40 in)

1346 mm (53 in)

1676 mm (66 in)

Welcome To Choose Required IT Certification Exams Online

New BICSI RCDDv14 Exam Questions To Pass The BICSI Registered Communications Distribution Designer Exam

Having the BICSI Registered Communications Distribution Designer – RCDDv14 free demo questions first:

Author