Updated CCNA Exam 200-301 Test Questions [2022] Real Materials For Pass Cisco CCNA Exam

Regina2022-02-25T07:50:55+00:00

Cisco Certified Network Associate (CCNA) certification requires to pass 200-301 exam. While planning to prepare for 200-301 Implementing and Administering Cisco Solutions certification exam well, you are recommended to choose the updated CCNA 200-301 test questions of ITExamShop to be an effective way of passing Cisco CCNA 200-301 exam successfully. Updated 200-301 exam questions are real, which have been verified by the top team, they guarantee that you can pass 200-301 Implementing and Administering Cisco Solutions certification exam in the first attempt with the real online materials of ITExamShop.

First to read Cisco CCNA 200-301 free demo questions before getting updated 200-301 test questions:

Page 1 of 3

1. Refer to the exhibit.

Which type of route does R1 use to reach host 10.10.13.10/32?

floating static route

host route

default route

network route

2. Which command enables a router to become a DHCP client?

ip address dhcp

ip helper-address

ip dhcp pool

ip dhcp client

3. Refer to the exhibit.

What is the effect of this configuration?

The switch port interface trust state becomes untrusted.

The switch port remains administratively down until the interface is connected to another switch.

Dynamic ARP inspection is disabled because the ARP ACL is missing.

The switch port remains down until it is configured to trust or untrust incoming packets.

4. How do TCP and UDP differ in the way that they establish a connection between two endpoints?

TCP uses synchronization packets, and UDP uses acknowledgment packets.

UDP uses SYN, SYN ACK and FIN bits in the frame header while TCP uses SYN, SYN ACK and ACK bits.

UDP provides reliable message transfer and TCP is a connectionless protocol.

TCP uses the three-way handshake and UDP does not guarantee message delivery.

5. Refer to the exhibit.

What does router R1 use as its OSPF router-ID?

10.10.1.10

10.10.10.20

172.16.15.10

192.168.0.1

6. Which mode allows access points to be managed by Cisco Wireless LAN Controllers?

autonomous

lightweight

bridge

mobility express

7. Refer to the exhibit.

If OSPF is running on this network, how does Router 2 handle traffic from Site B to 10.10.13.128/25 at Site A?

It sends packets out of interface Fa0/2 only.

It sends packets out of interface Fa0/1 only.

It cannot send packets to 10.10.13.128/25.

It load-balances traffic out of Fa0/1 and Fa0/2.

8. Refer to the exhibit.

Which password must an engineer use to enter the enable mode?

adminadmin123

default

testing1234

cisco123

9. Which 802.11 frame type is association response?

management

protected frame

control

action

10. Which two values or settings must be entered when configuring a new WLAN in the Cisco Wireless LAN Controller GUI? (Choose two)

management interface settings

QoS settings

Ip address of one or more access points

SSID

Profile name

Page 2 of 3

11. An engineer configured an OSPF neighbor as a designated router.

Which state verifies the designated router is in the proper mode?

Exchange

2-way

Full

Init

12. Refer to the exhibit.

Which command provides this output?

show ip route

show ip interface

show interface

show cdp neighbor

13. What are two reasons that cause late collisions to increment on an Ethernet interface? (Choose two)

when the sending device waits 15 seconds before sending the frame again

when the cable length limits are exceeded

when one side of the connection is configured for half-duplex

when Carner Sense Multiple Access/Collision Detection is used

when a collision occurs after the 32nd byte of a frame has been transmitted

14. Refer to the exhibit.

The show ip ospf interface command has been executed on R1.

How is OSPF configured?

The interface is not participating in OSP

A point-to-point network type is configured.

The default Hello and Dead timers are in use.

There are six OSPF neighbors on this interface.

15. A user configured OSPF in a single area between two routers A serial interface connecting R1 and R2 is running encapsulation PPP, by default, which OSPF network type is seen on this interface when the user types show ip ospf interface on R1 or R2?

port-to-multipoint

broadcast

point-to-point

nonbroadcast

16. Refer to the exhibit.

An extended ACL has been configured and applied to router R2. The configuration started to work as intended.

Which two changes stop outbound traffic on TCP ports 25 and 80 to 10.0.20.0/26 from the 10.0.10.0/26 subnet while still allowing all other traffic? (Choose two)

Add a “permit ip any any” statement to the begining of ACL 101 for allowed traffic.

Add a “permit ip any any” statement at the end of ACL 101 for allowed traffic.

The source and destination IPs must be swapped in ACL 101.

The ACL must be configured the Gi0/2 interface inbound on R1.

The ACL must be moved to the Gio/1 interface outbound on R2.

17. Which QoS Profile is selected in the GUI when configuring a voice over WLAN deployment?

Bronze

Platinum

Silver

Gold

18. Which attribute does a router use to select the best path when two or more different routes to the same destination exist from two different routing protocols?

dual algorithm

metric

administrative distance

hop count

19. Refer to the exhibit.

Which route does R1 select for traffic that is destined to 192 168.16.2?

192.168.16.0/21

192.168.16.0/24

192.168 26.0/26

192.168.16.0/27

20. When OSPF learns multiple paths to a network, how does it select a route?

It multiple the active K value by 256 to calculate the route with the lowest metric.

For each existing interface, it adds the metric from the source router to the destination to calculate the route with the lowest bandwidth.

It divides a reference bandwidth of 100 Mbps by the actual bandwidth of the existing interface to calculate the router with the lowest cost.

It count the number of hops between the source router and the destination to determine the router with the lowest metric.

Page 3 of 3

21. What is the default behavior of a Layer 2 switch when a frame with an unknown destination MAC address is received?

The Layer 2 switch drops the received frame.

The Layer 2 switch floods packets to all ports except the receiving port in the given VLA

The Layer 2 switch sends a copy of a packet to CPU for destination MAC address learning.

The Layer 2 switch forwards the packet and adds the destination MAC address to its MAC address table.

22. Refer to Exhibit.

An engineer is configuring the NEW York router to reach the Lot interface of the Atlanta router using interface Se0/0/0 as the primary path.

Which two commands must be configured on the New York router so that it can reach the Lo1 interface of the Atlanta router via Washington when the link between New York and Atlanta goes down? (Choose two)

ipv6 router 2000::1/128 2012::1

ipv6 router 2000::1/128 2012:1 5

ipv6 router 2000::1/128 2012::2

ipv6 router 2000::1/128 2023:2 5

ipv6 router 2000::1/128 2023::3 5

23. An organization has decided to start using cloud-provided services.

Which cloud service allows the organization to install its own operating system on a virtual machine?

platform-as-a-service

software-as-a-service

network-as-a-service

infrastructure-as-a-service

24. Which output displays a JSON data representation?

A)

Option A

Option B

Option C

Option D

25. Router A learns the same route from two different neighbors, one of the neighbor routers is an OSPF neighbor and the other is an EIGRP neighbor.

What is the administrative distance of the route that will be installed in the routing table?

110

115

26. Which mode must be used to configure EtherChannel between two switches without using a negotiation protocol?

auto

active

desirable

27. Which two capacities of Cisco DNA Center make it more extensible? (Choose two)

adapters that support all families of Cisco IOS software

SDKs that support interaction with third-party network equipment

customized versions for small, medium, and large enterprises

REST APIs that allow for external applications to interact natively with Cisco DNA Center

modular design that is upgradable as needed

28. Refer to the exhibit.

An engineer is bringing up a new circuit to the MPLS provider on the Gi0/1 interface of Router1. The new circuit uses eBGP and teams the route to VLAN25 from the BGP path.

What’s the expected behavior for the traffic flow for route 10.10.13.0/25?

Traffic to 10.10.13.0.25 is load balanced out of multiple interfaces.

Route 10.10.13.0/25 is updated in the routing table as being learned from interface Gi0/1.

Traffic to 10.10.13.0/25 is asymmeteical.

Route 10.10.13.0/25 learned via the Gi0/0 interface remains in the routing table.

29. Which type of address is the public IP address of a NAT device?

outside global

outsdwde local

inside global

insride local

outside public

inside public

30. Refer to the exhibit.

An engineer configured NAT translations and has verified that the configuration is correct.

Which IP address is the source IP?

10.4.4.4

10.4.4.5

172.23.103.10

172.23.104.4

Welcome To Choose Required IT Certification Exams Online

Updated CCNA Exam 200-301 Test Questions [2022] Real Materials For Pass Cisco CCNA Exam

First to read Cisco CCNA 200-301 free demo questions before getting updated 200-301 test questions:

Author