Updated Cisco SPCOR 350-501 Exam Questions - Preparation For Actual Cisco 350-501 Exam

Updated Cisco SPCOR 350-501 Exam Questions – Preparation For Actual Cisco 350-501 Exam

Regina2022-01-06T03:38:39+00:00

By Regina CCNP Service Provider, Cisco, Free Questions Online 350-501, 350-501 exam questions, 350-501 free questions, 350-501 real questions, 350-501 SPCOR

If you are planning to take 350-501 Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) certification exam, you should prepare with the most updated Cisco SPCOR 350-501 exam questions of ITExamShop. Cisco 350-501 exam questions updated by the top team of ITExamShop are based on the real Cisco 350-501 exam objectives, which could be the best preparation tool for actual Cisco 350-501 exam. The updated 350-501 exam questions of ITExamShop could be the finest way to not only get the far better real Cisco 350-501 SPCOR exam understanding but you can also get the possibility to have a much better assessment of the preparation for the real 350-501 exam questions.

Check Cisco 350-501 Free Demo Questions Before Buying Updated 350-501 Exam Questions

Page 1 of 3

1. Refer to the exhibit:

A network administrator wants to enhance the security for SNMP for this configuration.

Which action can the network administrator implement?

Re-configure to use SNMPv2 with MD5 authentication

Add a community string to the existing entry

Re-configure to use SNMPv3.

Maintain the configuration but switch to an encrypted password for device access through SSH

2. Which component is similar to an EVPN instance?

MPLS label

IGP router ID

VRF

router distinguisher

3. What occurs when a high bandwidth multicast stream is sent over an MVPN using Cisco hardware?

Option A

Option B

Option C

Option D

4. Refer to the exhibit:

BGPsec is implemented on R1. R2. R3. and R4 BGP peering is established between neighboring autonomous systems.

Which statement about implementation is true?

BGP updates from the eBGP peers are appended with an additional AS path value that is statically set by the domain administrator

BGP updates from the iBGP peers are appended with a community of local-as

BGP updates from the all BGP peers are appended with a community of no export

BGP updates from the eBGP peers are appended with a BGPsec attribute sequence that includes a public key hash and digital signature

5. TION NO: 91

Refer to the exhibit:

R1 and R2 are directly connected with Fast Ethernet interfaces and have the above configuration applied OSPF adjacency is not formed. When the debug ip ospf hello command is issued on R1. these log messages are seen.

Which command can be configured on routers R1 and R2 on fO/O interfaces to form OSPF adjacency?

ip ospf network non-broadcast

ip ospf network point-to- multipoint non-broadcast

ip ospf network point-to-point

ip ospf network broadcast

6. DRAG DROP

Drag and drop the multicast concepts from the left onto the correct descriptions on the right.

7. Refer to the exhibit:

In which way does router R1 operate differently than router R2?

R1 sends LSA type 2 only, while R2 sends type 1 and type 7 LSAs

R1 sends LSA types 1 and 2, while R2 sends type 1. 2. and 7 LSAs

R1 sends LSA type 2 only and R2 sends LSA type 1 only

R1 sends LSA types 5 and 7, while R2 sends type 1, 2, and 7 LSAs

8. Refer to the exhibit.

Which task completes the configuration?

Specify the maximum number of prefixes that R1 receives from neighbor 192.168.1.2.

Specify the source interface in the neighbor statement.

Specify the activate neighbor 192.168.1.2 under the IPv4 address family.

Specify the local-as value in the neighbor statement.

9. Refer to me exhibit.

A network engineer notices PE-21 convergence degradation due to the growing LSDB size of Level 2 areas in the network The engineer decides to migrate router PE-21 from an inter-area design to an intra-area implementation, inter-area routing must De accomplished via an ATT-bit set by the Level 1/Level 2 router.

Which configuration must the engineer implement on PE-21 to complete the migrate?

Option A

Option B

Option C

Option D

10. Refer to the exhibit.

The network team must implement MPLS LDP session protection with two requirements:

✑ Session protection is provided for core loopback IP addresses only.

✑ The LDP session must remain operational for one hour when the WAN link on PE-XR1 fails.

Which configuration must the team implement on PE-XR1?

Option A

Option B

Option C

Option D

Page 2 of 3

11. What is a constraint of Cisco MPLS TE tunnel configurations?

Tunnels cannot span multiple OSPF areas.

With ISIS as an IG

only older-style metrics are used.

Tunnels cannot be configured over IP unnumbered links.

QoS-aware tunneling is not supported.

12. What is a primary benefit of IPoATM or MPLS over ATM backbone service provider networks?

dedicated circuits

variable-length packets

isochronous system

fixed-length cells

13. After a possible security breach, the network administrator of an ISP must verify the times that several different users logged into the network.

Which command must the administrator enter to display the login time of each user that activated a session?

show netconf-yang sessions detail

show netconf-yang datastores

show platform software yang-management process

show netconf-yang sessions

14. Refer to the exhibit:

A network engineer is implementing a BGP routing policy.

Which effect of this configuration is true?

All traffic that matches acl10 is allowed without any change to its local-preference

All traffic that matches acl10 is dropped without any change to its local-preference

If traffic matches acl10, it is allowed and its local-preference is set to 300

All traffic is assigned a local-preference of 30O regardless of its destination

15. After a series of unexpected device failures on the network. a Cisco engineer is deploying NSF on the network devices so that packets continue to be forwarded during switchovers. The network devices reside in the same holding, but they are physically separated into two different data centers.

Which task must the engineer perform as part of the deployment?

implement OSPF to maintain the link-state database during failover.

implement VRFs ana specify the forwarding instances that must remain active during failover.

implement an L2VPN with the failover peer to share state Information between the active and standby devices.

implement Cisco Express Forwarding to provide forwarding during failover

16. Refer to the exhibit.

A network administrator is implementing IGMP to enable multicast feed transmission to the receiver.

Which configuration must the administrator deploy on GW1 to permit IGMP Joins only to the assigned (S, G) feed?

A)

Option A

Option B

Option C

Option D

17. How is a telemetry session established for data analytics?

A router initiates a session using the dial-out to a destination.

A destination initiate a session to a router.

The destination initiate a session using the dial-out more to the router.

A router requests the data using Teinet.

18. Refer to the exhibits:

R1 and R2 are directly connected and IS-IS routing has been enabled between R1 and R2

R1 message periodically Based on this output, which statement is true?

IS-IS neighbor authentication is failing for Level 2 first and then for Level 1 PDUs

1S-1S neighbor authentication is failing for Level 1 and Level 2 PDUs .

IS-IS neighbor authentication is failing for Level 1 PDUs only

IS-IS neighbor authentication is failing for Level 2 PDUs only.

19. 1.Refer to the exhibit:

This configuration is being applied on an IOS XR router.

Which statement about this configuration is true?

It is used to create a subscription to specify the streaming interval

It is used to identify traps for SNMP polling

It is used to identify MIB entries and has a list of YANG models

It is used to create a sensor-group and has a list of YANG models for streaming

20. Refer to the exhibit:

What does the REST API command do?

It retrieves the information requested by Descriptions xml

It removes the information identified by Descriptions xml

It executes the commands specified in Descriptions xml

It displays the information identified by Descriptions xml

Page 3 of 3

21. How much must the MTU be increased when configuring the 802.1q VLAN tag?

2 bytes

4 bytes

8 bytes

12 bytes

22. A network engineer must configure a router for Flexible NetFlow IPFIX export. The IP address of the destination server is 172.17.12.1 The source address must be set to the Loopback0 IPv4 address and exported packets must be set to DSCP CS3. The TTL must be 64 and the transport protocol must be set to UDP with destination port 4739.

Which configuration must the engineer apply to the router?

Option A

Option B

Option C

Option D

23. Refer to the exhibit:

What does this value mean when it is received in XML?

It shows the ending of the script

It indicates a break in a sequence

It indicates a value assigned by a network administrator to tag a route

It means a data field is blank

24. Refer to the exhibit.

Router R1 is reporting that its BGP neighbor adjacency to router R2 is down, but its state is Active as shown.

Which configuration must be applied to routers R1 and R2 to fix the problem?

A)

Option A

Option B

Option C

Option D

25. Refer to me exhibit.

A network operator recently configured BGP FlowSpec for me internal IT network.

What will be inferred from the configuration deployed on me network?

The policy is configured locally on CSRl and drops all traffic for TCP ports 80 and 443

The policy is learned via BGP FlowSpec and drops all traffic for TCP ports 80 and 443

The policy is warned via BC FlowSpec aid has active traffic

The policy is configured locally on CSR1 and currently has no active traffic

26. What do Ansible and Salt Stack have in common?

They both use DSL configuration language

They both use YAML configuration language

They both have agents running on the client machine

They both can be designed with more than one master server

27. Refer to the exhibit:

An engineer is preparing to implement data plane security configuration.

Which statement about this configuration is true?

Router 2 must configure a route to null 0 for network 192 168.1 0/24 for the RTBH implementation to be complete.

Router 1 is the trigger router in a RTBH implementation.

Router 1 must be configured with uRPF for the RTBH implementation to be effective.

Router 2 is the router receiving the DDoS attack

28. Which type of attack is a Protocol attack?

HTTP flood

TFTP flood

SYN flood

Slowlorls

Welcome To Choose Required IT Certification Exams Online

Updated Cisco SPCOR 350-501 Exam Questions – Preparation For Actual Cisco 350-501 Exam

Check Cisco 350-501 Free Demo Questions Before Buying Updated 350-501 Exam Questions

Author